Hanging wallpaper is not difficult when there are specific instructions to take. Is it time to improve your home or office?

If wallpaper is a new venture for you, be certain to select your type carefully by reading the various kinds at the store. Based upon which kind you select, there may be some varied installation possibilities. The pre-pasted versions combine a dry paste onto the back of the surface. This is initialized by using water, as opposed to unpasted wallpapers require a wet paste applied with installation. Typically, the installation strategy is the same although depending on which sort you use the guidelines may vary.



Measure, cut, activate with H20 or paste and place are the general guidelines for installing wallpaper.

Wall Preparation

Your surface area and work area needs to be clean and clear before wallpaper installation. Ensure that all electrical outlets are switched off and take off any wall fixtures. Properly clean and organize wall surfaces by eradicating paste residue and previous wallpaper. TSP and alternative wall cleaners are a good idea.

Count on a premixed universal primer designated for wallpaper to make sure your surface is prepared. It is essential to prime the wall, particularly when working with unpasted wallpaper versions as it enables the wallpaper to come off easier.

Measure & Activate the Paper

The size of the wall is your initial measurement. Next, add four inches and then cut your wallpaper. You'll need the paper to overlap the ceiling and the baseboard by approximately 2 inches.

Take pattern matching into account via straight across, drop match, or random.



If hanging unpasted wallpaper…

For unpasted wallpaper, many prefer to administer the paste onto the wall, while others put it directly to the wallpaper. If you apply the paste to the wall surface, cover the area for one strip only and make certain to apply the product evenly. When pasting the wallpaper, begin in the centre and work away towards the edges as you evenly coat the wallpaper. Next, carefully fold the pasted sides of the moistened strip together with each other and allow them to relax for three minutes. This procedure is called booking.

Experiment to see if you prefer pasting unpasted versions by applying the paste to the paper or the wall. Only deal with one region at a time if you are evenly applying the paste directly on the wall. If you're pasting the wallpaper, carefully apply an even coat to the back of the wallpaper. Begin in the middle of the wallpaper section and move toward the external edges. Booking the wallpaper is really a necessary step that is completed by loosely folding the moistened strip of wallpaper and placing the pasted pieces together. Enable the booking aka folded wallpaper to stay in this manner for 3 minutes.

Pro Tip: If hanging up heavyweight wallpapers, particularly unpasted designs with flock, cork, or embroidery, choose a clear, stain-free heavyweight pre-mixed paste adhesive instead of a light-medium weight clear paste for best results.

When hanging pre-pasted wallpaper…

Take your cut strip and roll it loosely with pasted segment out and patterned side in. Energize the paste by submerging the rolled piece for 30 seconds into tepid to warm water. Alternatively, you can use a Wallpaper Hand Sprayer to achieve a similar effect by activating the paste with a fine mist of clean water to the pasted area.

Spray the paper in long strokes running the length of the wallpaper thoroughly saturate the strip. Take extra care around the edges to generate even watering. Next, fold each end section of the moistened strip toward the middle with pasted sides together. Don’t permit the edges to dry out by making sure they are in-line. Lastly, roll up the strip much like a loose newspaper and give it time to sit for 3 minutes to permit the paper to relax and the paste to become fully activated.



Hanging your first strip

Once the booking is done, take your strip to the wall. Carefully unfold the product and place it. Let the wallpaper overhang on the ceiling along with the baseboard. Carefully press out any air bubbles by using a smoothing brush, a broad knife, or a plastic smoother. Press the wallpaper to guarantee appropriate wall contact. Don’t distort or stretch out the wallpaper. Work with a seam roller to carefully flatten the seams.

Proceeding to the second strip

When butting the next section up to the first strip, place the second wallpaper sheet to the edge of the first. Press and even out firmly. Wash the baseboard and ceiling after to eliminate any residual paste. The aim is for your seams to enjoy a tight, vertical fit. Ensure there aren't any air bubbles in the paste.

Once you have fitted three panels smoothly to the wall and eradicated excess paste, set aside a second to examine your work. Note the pattern consistency and the color matching. Should you be satisfied, keep setting up three panels each time and checking them after. Matching patterns or geometric designs may necessitate extra selvage pruning to create colour coordinating across seams. As soon as your eyes and arms are tired, have a break and have some rest. Never hurry a wallpaper project. Proceed with the above steps to hang the rest of your pieces. Lastly, mindfully cut the extra trim along the ceiling and baseboards. Use a razor knife as well as a guide to slowly get rid of the excess without tearing.